Compiling GNS3 under Linux

I recently had cause to run GNS3 on Linux as I needed to support a cloud interface using VLANs: I needed to link connections to some virtual routers out onto a physical interface, with each link as a separate VLAN.  OS X doesn't support this (it seems - you can configure it, but it doesn't appear to work), whereas Linux does.

More on that later, but I found this guide very useful for setting up GNS3 on Ubuntu 14.04 Desktop and it worked fine in a VMware VM on my laptop:

http://www.firstdigest.com/2014/12/gns3-1-2-1-installation-on-ubuntu-14-04/

DHCP, RPF verify, FHRP and ECMP - when protocols collide

I've been gradually enabling ECMP (Equal-Cost MultiPath) routing on parts of the University network as part of a prelude to the new data centre network and to improve performance generally (by making use of the dual downstream interfaces into institutions).

For the most part, this is fairly straightforward and just worked - I'll explain what was needed in each case in a future post (as MPLS VPN works slightly differently and needs some special consideration), but I did get a nasty problem which broke DHCP relaying in some places that I'll cover here.

How DHCP relaying works

First, let's review how DHCP relaying works (what you get when you do ip helper-address ... on a Cisco router interface towards clients).  Consider the following network:

When a client on the subnet 192.168.1.0/24 wants to DHCP, the following happens initially:

1. The client sends out a DHCP DISCOVER message from 0.0.0.0 (as it doesn't know its IP address or even subnet, yet) on UDP port 68 (the DHCP client port) to all-hosts broadcast (255.255.255.255) port 67 (DHCP server).
2. The DHCP relay agent (which is normally the router) will receive this broadcast and forward it as a unicast packet to the DHCP server listed in the ip helper-address ... interface command.  This will be from the router's interface address (this is the critical bit) - 192.168.1.253, in the above example, port 67 to the DHCP server, port 67.
3. The DHCP server will receive the DISCOVER and, assuming it has an address (and other information) to give to the client, it will send a DHCP OFFER message back to the router to be relayed onto it.  This will be the reverse of the packet just received: going from the DHCP server's address, port 67 to the router's interface address, port 67.
4. The router will receive the reply and unicast it back to the client, sending it from its interface IP address, port 67 to the client's prospective IP address, port 68.

This all works fine and, assuming the client wants to take the address, it will send a DHCP REQUEST (using the same process) and receive a DHCP ACK back from the server so it can begin using the address.

How DHCP relaying doesn't work

Now consider what happens when the same DHCP DISCOVER is relayed by the other client subnet router, without ECMP:

Here, something goes wrong at step 3, trying to return the DHCP OFFER to the relaying router:

1. Because the backbone network (depicted with the cloud symbol) only knows about routing to the client subnet as a whole /24 (not the individual routers' addresses), it routes the packet via 192.168.1.253.
2. 192.168.1.253 treats 192.168.1.252 as just another host on the client subnet and forwards it out of its interface onto that subnet.
3. Because 192.168.1.252 has anti-spoofing blocks in place on the client subnet interface, it rejects this packet as the source address is that of the DHCP server: an invalid address from the client subnet.

With this configuration, typical for a network with a FHRP (First Hop Redundancy Protocol) such as HSRP or VRRP is in use, half of the DHCP replies (the ones relayed via one of the two routers) will be lost when they're returned to the relaying routers.

However, this in itself isn't particularly a problem in that both routers will relay the same packet to the DHCP server, resulting it receiving two copies of each DISCOVER [but with different relay agent / forwarder addresses], causing two OFFERs to be returned; the clients will not miss out as they'll get one of the two copies.  This is why I've never noticed this problem, even though it's been going on for years: the clients have still got their address and worked.

(Actually, I was sort-of aware of this problem, as it prevented pinging one of the routers' own addresses on a particular interface, if the source of the ping was elsewhere on the network.  However, that's just been a minor inconvenience and not service-affecting; I never realised that would also be affecting DHCP.)

Combining with ECMP

When this situation is combined with ECMP this can get messy: the returned DHCP OFFERs (and ACKs) might be returned to either of the two client subnet routers.  The routers' addresses are often 1 number offset (e.g. 192.168.1.252 vs .253) which will likely mean they each take a different path.

If the path for packets to the .253 relay address happen to go directly to the .253 router, all is fine.  Same with .252.

However, if you're really unlucky (and, of course, we were, in some situations), ECMP will return the .253 packet via the .252 router and the .252 packet via .253.  This results in both replies being rejected and the client getting neither of the responses.

Fixing the problem and creating another

I couldn't find any way to direct the replies back to the correct router (e.g. by advertising the router's interface IP address into OSPF as a /32), so dealing with them being rejected by the anti-spoofing protection seemed the only solution.

As I've written, I've been looking at the ip verify unicast source ... command recently, and it seemed a good opportunity to employ that, rather than modify lots of access control lists.  According to Cisco's documentation, that command has a special feature in to handle DHCP:

"Unicast RPF will allow packets with 0.0.0.0 source and 255.255.255.255 destination to pass so that Bootstrap Protocol (BOOTP) and Dynamic Host Configuration Protocol (DHCP) functions work properly."

— from the IOS Security Configuration Guide for IOS 12.2SX

Sounds good, except that doesn't handle the source addresses of relayed DHCP replies.  It would be nice if this included "packets with a source address of the interface ip helper-address and port 67, destined for the router's interface address port 67", but it doesn't.

However, the command has a feature to allow packets matching an access list to be accepted, even if they fail the RPF check.  It's configured as follows:

ip access-list extended 1301
 permit udp host DHCP-SERVER eq 67 192.168.1.0 0.0.0.255 eq 67
!
interface ...
 ip address 192.168.1.253 255.255.255.0
 standby ip 192.168.1.254
 ip verify unicast source reachable-via rx 1301

This will allow the initial DHCP DISCOVER in (as described in the Cisco documentation), regular 192.168.1.0/24 traffic (due to the RPF check) AND traffic from the DHCP server on port 67 to an address on the same subnet port 67 (which is less tedious than putting the interface IP address itself as it can be copied to the other router without modification).  This change can be combined with a simplification of the interface access lists (if used).  So, I implemented a few of these and all looked hunky dory.

The IP Input process - my old nemesis

However, a little while later, we started getting alarms for CPU usage on the Catalyst 6500-E routers.  A show process cpu sorted command showed high load caused by the IP Input process.

This is usually caused by excessive traffic being forwarded ("punted" in Cisco parlance) to the Route Processor (RP) for handling.  We can capture and display these with the following commands:

router# debug netdr capture rx
router# show netdr captured-packets

(Use debug netdr clear-capture to clear the buffer and our old friend undebug all to switch it off.)

The packets being punted all appeared to be regular data - nothing complicated like DHCP which needs special processing, so I started doing some more reading and found a document on Cisco's website explaining how this configuration is handled on a 6500:

"For unicast RPF check without ACL filtering, the PFC3 provides hardware support for the RPF check of traffic from multiple interfaces. 

For unicast RPF check with ACL filtering, the PFC determines whether or not traffic matches the ACL. The PFC sends the traffic denied by the RPF ACL to the route processor (RP) for the unicast RPF check. Packets permitted by the ACL are forwarded in hardware without a unicast RPF check." 

— from the IOS Network Security guide for IOS 12.2SX on Catalyst 6500 with PFC3

So it appears that, when you use an ACL, all the traffic not matching the ACL will get punted to the RP.  Excellent.

Fixing the problem for good

So, I backtracked on using the ip verify unicast ... command and reverted to using our old inbound access lists to protect against address spoofing.  These now have an extra entry and look as follows:

ip access-list extended in-subnet
 permit ip 192.168.1.0 0.0.0.255 any
 permit udp any eq bootpc host 255.255.255.255 eq bootps
 permit udp host DHCP-SERVER eq bootps 192.168.1.0 0.0.0.255 eq bootps
 deny ip any any

This appears to do the trick and doesn't involve the RP on the router going bananas.  Given this problem, I think I'll abandon using the ip verify unicast ... command!

(Update 2018-02-01 — we have since installed Catalyst 6807-XLs with Supervisor 6Ts and came up with a final solution.  I've described that on a separate blog post.)

"mpls ip ttl-expiration pop 1"

I encountered an odd problem when tracerouting from outside the University network to a host in the data centre network in my GNS3 simulation:

HOST-JANETW#traceroute 131.111.8.31

Type escape sequence to abort.

Tracing the route to RAVEN.CAM (131.111.8.31)

  1 GW-JANETW.JANETW.JA (128.4.0.254) 76 msec 76 msec 72 msec

  2 JANETW.ENETW.NET (146.97.41.246) 196 msec 96 msec 112 msec

  3  *  *  * 

  4  *  *  * 

  5 DCW-CUDN.DCW-SRV.NET (193.60.88.2) 176 msec 180 msec 144 msec

  6 RAVEN.CAM (131.111.8.31) 188 msec 180 msec 184 msec

[For reference, these hostnames are not the same as the real ones, but the naming system works by using OTHER-ROUTER.THIS-ROUTER.DOMAIN - so JANETW.ENETW.NET is the IP address of ENETW on the link to/from JANETW.]

Hops 3 and 4 went missing, which are those to MILL from ENETW and then to DCW[-CUDN] from MILL; once we reach DCW-SRV from DCW[-CUDN] we get responses again.  (The two DCW names are because they're different VDCs on the same Nexus 7010.)  This is shown below, with the missing hops at the tips of the red arrows:

This puzzled me for about an hour and a half - I was checking routes and trying pings from the affected hosts back to the source, which were working OK.  I then starting poking about in more details to check what exactly happened to the packets...

Plain-IPv4-over-MPLS when you don't expect it

The first thing was to see what happened to the packet on ENETW by consulting CEF to see what it would do with a packet destined for 131.111.8.31:

BDR-ENETW#show ip cef 131.111.8.31 detail 

131.111.8.0/23, epoch 0

  recursive via 193.60.88.2

    nexthop 192.84.5.133 Ethernet1/1 label 33

This shows the packet was matching the 131.111.8.0/23 route which should be sent via 193.60.88.2 (the interface on DCW-SRV coming from DCW[-CUDN]), which is reached recursively by using a next hop of 192.84.5.133 (the interface on MILL at hop 3, coming in from ENETW).  The important bit is to note that the packet will be forwarded out of interface Ethernet1/1 with MPLS label 30.

Dissecting this (as an aside - just to check there wasn't anything completely screwy) - 131.111.8.0/23 is an eBGP route to AS65110 (the server network) learnt from 193.60.88.2:

BDR-ENETW#show ip route 131.111.8.31

Routing entry for 131.111.8.0/23

  Known via "bgp 64602", distance 200, metric 0

  Tag 65110, type internal

  Last update from 193.60.88.2 01:41:18 ago

  Routing Descriptor Blocks:

  * 193.60.88.2, from 192.84.5.240, 01:41:18 ago

      Route metric is 0, traffic share count is 1

      AS Hops 1

      Route tag 65110

193.60.88.2 is, in turn, reached via OSPF with next hop 192.84.5.133, as CEF showed:

BDR-ENETW#show ip route 193.60.88.2

Routing entry for 193.60.88.2/32

  Known via "ospf 1", distance 110, metric 55, type extern 1

  Last update from 192.84.5.133 on Ethernet1/1, 01:45:33 ago

  Routing Descriptor Blocks:

  * 192.84.5.133, from 192.84.5.248, 01:45:33 ago, via Ethernet1/1

      Route metric is 55, traffic share count is 1

So, back to the label - let's see what that's for:

BDR-ENETW#show mpls ip binding remote-label 33 neighbor 192.84.5.133

  193.60.88.2/32

        out label:    33        lsr: 192.84.5.250:0   inuse

Here, I didn't expect MPLS to be in use as the destination address of the packet isn't one that we advertise labels for via LDP: we limit those to the backbone router loopback addresses and the outside addresses of eBGP peers to which we have inter-AS MPLS VPNs.

However, as our server network does operates as a separate AS from the backbone and we use MPLS forwarding between it and the backbone, we do advertise labels for its outside addresses - including 193.60.88.2/32: ENETW has labelled the packet for forwarding across the backbone to DCW-SRV because it has a BGP next hop with a label available.

Next step is to work out what happens to this MPLS frame...

Traceroute over an MPLS network

So, assuming that ENETW does the correct thing and sends the packet on via MPLS to MILL, lets see what that does by debugging ICMP and trying the traceroute again:

CORE-MILL#debug ip icmp

ICMP packet debugging is on

CORE-MILL#

Apr  8 19:53:01.591: Adding 4 bytes of label stack

Apr  8 19:53:01.595: MPLS: ICMP: time exceeded (time to live) sent to 128.4.0.1 (dest was 131.111.8.31)

This shows the MPLS frame is received and the TTL expired (by default, the PE router which turns the packet from a plain IPv4 packet into a labelled MPLS frame will copy the increasing TTL [as generated by traceroute]).  The P router (MILL) unwraps the packet inside and generates the 'TTL exceeded' ICMP message.

The critical bit, however, is that the P router will then label the packet up with its original MPLS label and forward it on to the destination (with a TTL reset to 255); it does NOT return it directly to the sender.  It has to do this as the IP addresses using the MPLS frame may not be ones which exist in the same routing space as the P router.

I verified all this by running Wireshark on the virtual interfaces inside GNS3 (incredibly useful that!) and checking it all looked the way I expected.

This I knew and understood and had investigated in the past (although not in an inter-AS situation) - what I hadn't thought of was what happens next...

The egress PE router

When the egress PE router receives the labelled ICMP 'TTL exceeded' packet, it unwraps it and tries to forward it on to the destination.  In this case, the PE router is DCW-SRV (in the server network) trying to return a packet with a source address of 192.84.5.133 to 128.4.0.1 (HOST-JANETW; an imaginary host, the one my traceroute was initiated from).  This is where things fail...

Because of the recent IP unicast RPF verification testing I've been doing, that source address is blocked from entering the backbone from the server network by the distribution routers to prevent address spoofing: the server network is not allowed to originate addresses it is not responsible for routing.

This can be confirmed by looking on the distribution router, DCW[-CUDN], part of the backbone network:

DIST-DCW#show ip int e1/2 | begin verify

  IP verify source reachable-via RX, ACL 10

   108 verification drops

   0 suppressed verification drops

   0 verification drop-rate

Some debugging shows the naughty source address:

DIST-DCW#debug ip cef drops rpf         

IP CEF drops for RPF debugging is on

DIST-DCW#

*Apr  8 20:08:38.171: CEF-Drop: Packet from 192.84.5.133 via Ethernet1/2 -- via-rx

DIST-DCW#

In the words of Colonel Hans Landa: that's a bingo!  The whole thing is illustrated below, with the rejected ICMP message from the DCW-SRV PE router being marked with a X in red:

MPLS Traceroute showing ICMP message from PE router being rejected due to RPF

It also explains why I'd never seen this problem with the Computer Laboratory in my simulation before, as I'd never bothered blocking traffic from other ASs to prevent address spoofing: I'd only ever tested filtering prefixes over eBGP; traffic filtering is something we've always done on the real network through access lists and not of interest in the simulation.

Solving the [non] problem

Once I'd worked out what the actual problem was, solving it turned out to be trivial...

In reality, this problem turns out to be academic: on our real network, we run with "no mpls ip propagate-ttl forwarded" configured on our PE routers, which prevents the TTL of the incoming packet from being copied into the MPLS frame.  This means that the TTL should never expire when crossing the backbone and those hops simply won't show up in a traceroute (so successful hops 5 and 6 will become hops 3 and 4).

However, in my GNS3 simulation, I like to expose the intermediate hops to verify complete paths from end station hosts for diagnostic and investigatory purposes.  Indeed, the reason I spotted the problem was whilst testing the paths for traffic when various failures occur, by shutting down partso the simulation.

The solution to this is to use the "mpls ip ttl-expiration pop 1" command - this causes MPLS frames with only a single label depth (which will be plain IPv4-over-MPLS frames) to be returned directly to the sender by the P router, rather than forwarding it on to the PE router to be bounced back.  As such, there is no problem with address spoofing as the IP packet starts its life inside the backbone itself.

After doing the later, my traceroute works:

HOST-JANETW#traceroute 131.111.8.31

Type escape sequence to abort.

Tracing the route to RAVEN.CAM (131.111.8.31)

  1 GW-JANETW.JANETW.JA (128.4.0.254) 16 msec 16 msec 8 msec

  2 JANETW.ENETW.NET (146.97.41.246) 20 msec 52 msec 20 msec

  3 ENETW.MILL.NET (192.84.5.133) [MPLS: Label 33 Exp 0] 68 msec 52 msec 24 msec

  4 MILL.DCW.NET (192.84.5.154) [MPLS: Label 16 Exp 0] 48 msec 68 msec 48 msec

  5 DCW-CUDN.DCW-SRV.NET (193.60.88.2) 80 msec 88 msec 68 msec

  6 RAVEN.CAM (131.111.8.31) 104 msec 56 msec 112 msec

You can even see the MPLS labels used in the previously-missing hops being returned in the ICMP extension block.

One thing that this has shown up is that, once the new data centre network is installed, traceroutes into our server network will not expose the backbone network router hops.  That wasn't something I was expecting and could be confusing for others.

Current GNS3 environment

I've been updating my GNS3 environment (I last posted about this back in August 2013) with some changes recently.  The new model (as of 6th April 2015) is updated to work in GNS3 1.3.0 below:

I added MPLS just under a couple of years ago (I started planning it in mid-2013 and implemented it late in the year), including an EoMPLS xconnect, as well as IPv6 multicast.  The recent changes however are:

• Added the data centre network (being implemented at the moment) — interfacing to the backbone in the same way as a regular institutional network.
• Added a second Janet connection (to be implemented soon, when the routers arrive!), with separate Janet router (janetw) and CUDN border router (enetw).  This involved adjusting the internal OSPF link costs and BGP advertisements.
• Added the NAT service using a pair of IOS routers (instead of the real ASAs).
• Expanded the Medical School network with a local, static router and added a directly-routed WBIC [Wolfson Brain Imaging Centre] host instead (which doesn't use the Medical School PoP connection, but this doesn't matter for the simulation).
• Removed MRC CBSU [Cognition and Brain Sciences Unit] as they aren't doing anything particularly interesting any more (they were advertising a /23 we had to relay to Janet and expose and trim the AS path from, but we now do this for them; Engineering now do this, anyway).

IP unicast RPF source verification

We currently block against spoofed addresses using extended router access lists on the inbound interfaces from institutions (departments and colleges).  Whilst this works, it is very tedious to maintain these access lists (including keeping them synchronised across routers, which we do via a complex external script mechanism).

However, Cisco IOS has a feature called "IP Unicast Reverse Path Forwarding Source Verification" which can be used to block spoofed addresses from entering via a routing interface which I've been meaning to look at for ages.

The feature is activated using the interface command "ip verify unicast source reachable-via rx" - this blocks any traffic entering via that interface if it wouldn't be used to send outbound traffic to the source address: an RPF (Reverse Path Forwarding) check, exactly as multicast does.

Once the feature is applied, the "show ip interface" command will display the number of packets which have been blocked due to it:

JANETC#show ip int e1/3 | begin verify

  IP verify source reachable-via RX

   9 verification drops

   0 suppressed verification drops

   0 verification drop-rate

Asymmetric paths

For the feature to work, it is essential that traffic paths are symmetrical across any interfaces on which it is used.  This is normally the case for simple edge interfaces as there can only be a single path to the address ranges which are connected and statically routed across them.

However, on links where dynamic routing takes place, traffic can arrive via the non-reverse path, resulting in asymmetric paths.  On the internal links of a network, this is usually not a problem as long as the traffic across those can be trusted, as long as the edge of the network is protected.

The only place where this presents a problem is where dynamic routing takes place across an administrative boundary (such as those between ASs where eBGP peerings are used).  Here, the obvious solution is to fix the traffic paths such that they are symmetric, which is required if multicast is to function correctly anyway.

However, the verification feature supports an access list to allow packets to pass, even in the event of the RPF check failing.  This is specified on the end of the "ip verify ..." command, e.g.:

ip access-list standard 3

 permit 128.232.0.0 0.0.255.255

 permit 129.169.0.0 0.0.255.255

 permit 131.111.0.0 0.0.255.255

!
interface Ethernet1/3
 ip verify unicast source reachable-via rx 3

The number of packets which have been permitted through this mechanism will also show up in the IP interface information under "suppressed verification drops":

JANETC#show ip int e1/3 | begin verify

  IP verify source reachable-via RX, ACL 3

   31 verification drops

   39 suppressed verification drops

   0 verification drop-rate

Interaction with access lists

When combining this feature with inbound access lists on an interface, the access lists are applied BEFORE the source address verification.  As such, packets which the access list blocks will not show up in the address verification counts, shown above.

The two features can be usefully combined, as access lists do not need to be written to handle the validation of source addresses - they can just permit or deny the traffic required, based on ports and protocols, leaving source address validation to be done by the verification feature.  This is especially useful when multinetting is used.  I expect this will allow us to simplify many of our access lists.

NAT in a VRF on a 7200 (in GNS3)

An interesting aside here — I've been updating my GNS3 model of the University of Cambridge network to include a second connection to Janet (the UK Education and Research network).  We want to run the links and NAT boxes (which are ASA5580-20s) in active-active mode so I've had to add those.

I can't be bothered trying to wrestle with a pair of ASAs in multi-context mode (which you need for active-active) so I looked at using NAT under IOS on a 7200 (the platform we use as the router equivalent of our Catalyst 6500-Es in GNS3).  I don't need stateful switchover, but I do want the basic service to failover in the simulation.

This turns out to be very simple as the 7200s support NAT in VRFs and we can use HSRP to do the active-active balancing.

Background

CUDN border and NAT from GNS3

Our NAT service works by putting an ASA on a stick, attached to the border routers.  Some PBR (Policy Based Routing) redirects traffic destined for the internet (via Janet) to the ASA that comes from University-wide private addresses (which are RFC1918 addresses we route internally and NAT when they leave).

This arrangement means that only traffic to be NATed needs to go through the ASAs: IPv4 public IP addresses and IPv6 flow straight through, so we don't have to worry about handling those, which not only reduces load on the ASAs but also means we don't have to work out how to get things like multicast through them.

There are two ASAs operating in a pair, handling roughly half of the private addresses each.  This is done by putting half of the private addresses through one context, normally active on one box, and the other half through a second context, normally active on the other.  If either fail, one ASA takes over all the load.

The inside of the ASAs is on a /29 link subnet with static routing: the ASAs provide a redundant first hop address for traffic to them for the router to redirect traffic two.  The outside is a /24 block to provide a pool of public IP addresses to NAT behind.  That subnet is a effectively a regular client subnet.

NATed traffic coming back in goes to the public range, gets de-NATed by the ASAs and sent back into the network on the inside /29.

The router provides first hop redundant gateways on both the inside and outside networks, although in practice there is only one at present.

There are separate inside /29s and outside /24s for each half of the private addresses to be NATed.

In the GNS3 simulation, we're going to replace the ASAs with IOS routers doing NAT.

Router configuration

The configuration of the routers doing the PBR is identical to the real production ones.

First, we create the interfaces to link to the NAT - this is the configuration for the first router, which is going to handle the outside range 131.111.184.0/24 by default (the other outside range will go through 131.111.185.0/24 to load balance - see the BGP configuration later):

interface Ethernet1/2.1981

 description nat-1-outside

 encapsulation dot1Q 1981

 ip address 131.111.184.253 255.255.255.0

 no ip proxy-arp

 standby version 2

 standby 81 ip 131.111.184.254

 standby 81 timers 1 3

 standby 81 priority 200

 standby 81 preempt

 standby 81 track 30 decrement 50

!

interface Ethernet1/2.1982

 description nat-1-inside

 encapsulation dot1Q 1982

 ip address 193.60.92.34 255.255.255.248

 no ip proxy-arp

 standby version 2

 standby 82 ip 193.60.92.33

 standby 82 timers 1 3

 standby 82 priority 200

 standby 82 preempt

 standby 82 track 30 decrement 50

!

interface Ethernet1/2.1983

 description nat-2-outside

 encapsulation dot1Q 1983

 ip address 131.111.185.253 255.255.255.0

 no ip proxy-arp

 standby version 2

 standby 83 ip 131.111.185.254

 standby 83 timers 1 3

 standby 83 priority 190

 standby 83 preempt

 standby 83 track 30 decrement 50

!

interface Ethernet1/2.1984

 description nat-2-inside

 encapsulation dot1Q 1984

 ip address 193.60.92.42 255.255.255.248

 no ip proxy-arp

 standby version 2

 standby 84 ip 193.60.92.41

 standby 84 timers 1 3

 standby 84 priority 190

 standby 84 preempt

 standby 84 track 30 decrement 50

Then we create access lists to match the private address to be NATed - we use all of 172.16.0.0/12, except for 172.31.0.0/16 (don't ask!):

ip access-list extended nat-1_clients

 deny   ip any 128.232.0.0 0.0.255.255

 deny   ip any 129.169.0.0 0.0.255.255

 deny   ip any 131.111.0.0 0.0.255.255

 deny   ip any 192.18.195.0 0.0.0.255

 deny   ip any 193.60.80.0 0.0.15.255

 deny   ip any 193.63.252.0 0.0.1.255

 permit ip 172.16.0.0 0.7.255.255 any

 deny   ip any any

!

ip access-list extended nat-2_clients

 deny   ip any 128.232.0.0 0.0.255.255

 deny   ip any 129.169.0.0 0.0.255.255

 deny   ip any 131.111.0.0 0.0.255.255

 deny   ip any 192.18.195.0 0.0.0.255

 deny   ip any 193.60.80.0 0.0.15.255

 deny   ip any 193.63.252.0 0.0.1.255

 permit ip 172.24.0.0 0.3.255.255 any

 permit ip 172.28.0.0 0.1.255.255 any

 permit ip 172.30.0.0 0.0.255.255 any

 deny   ip any any

We then create the route-maps to do PBR and redirect traffic across the /29 'inside' links:

route-map nat_redirect permit 110

 match ip address nat-1_clients

 set ip next-hop 193.60.92.38

!

route-map nat_redirect permit 120

 match ip address nat-2_clients

 set ip next-hop 193.60.92.46

... and attach them to the inside interfaces (linking to the core routers):

interface Ethernet1/0

 description CORE-CENT

 ip policy route-map nat_redirect

!

interface Ethernet1/1

 description CORE-MILL

 ip policy route-map nat_redirect

I mentioned we were going to use this router to handle the outside range 131.111.184.0/24 and the other 131.111.185.0/24.  To steer inbound traffic via this router, we want to advertise that prefix to Janet explicitly, so we need to add this to our BGP configuration:

router bgp 64602

 address-family ipv4 unicast

  network 131.111.184.0 mask 255.255.255.0

 exit-address-family

 !

 address-family ipv4 multicast

  network 131.111.184.0 mask 255.255.255.0

 exit-address-family

And also add that range to the outbound prefix list - I've created a new prefix-list under a specific name as I think it best to keep lists the same across routers, if their names are the same - these are not, so I've changed it on each:

ip prefix-list janetc-out_prefixes seq 5 permit 128.232.0.0/16

ip prefix-list janetc-out_prefixes seq 10 permit 129.169.0.0/16

ip prefix-list janetc-out_prefixes seq 15 permit 131.111.0.0/16

ip prefix-list janetc-out_prefixes seq 20 permit 192.18.195.0/24

ip prefix-list janetc-out_prefixes seq 25 permit 192.84.5.0/24

ip prefix-list janetc-out_prefixes seq 30 permit 192.153.213.0/24

ip prefix-list janetc-out_prefixes seq 35 permit 193.60.80.0/20

ip prefix-list janetc-out_prefixes seq 40 permit 193.63.252.0/23

ip prefix-list janetc-out_prefixes seq 45 permit 131.111.184.0/24

Finally, you may have spotted the track directive to HSRP above, in the interface definitions.  This is to cause HSRP to lower its priority, if this router loses direct connectivity to Janet.  The 7200 can't track the metric of a BGP router (unlike a Catalyst 6500), so I've just made it track the interface connecting to Janet:

track 30 interface Ethernet1/3 ip routing

This causes the gateways on the outside and inside interfaces to be handled by the router which has the best connectivity to Janet.

NAT configuration

The 7200 supports NAT in VRFs - while we don't strictly need to use them, it is a nice way of keeping the routing tables for the two NAT context separate (otherwise it wouldn't be clear which outside gateway was going to be used as the default route back to the router to go on to Janet).

First, create the VRFs:

vrf definition nat-1_vrf

 rd 64602:1981

 address-family ipv4

 exit-address-family

!

vrf definition nat-2_vrf

 rd 64602:1983

 address-family ipv4

 exit-address-family

Then some access lists to identify the clients to be NATed:

ip access-list standard nat-1-clients

 permit 172.16.0.0 0.7.255.255

!

ip access-list standard nat-2-clients

 permit 172.24.0.0 0.3.255.255

 permit 172.28.0.0 0.1.255.255

 permit 172.30.0.0 0.0.255.255

Create the two NAT pools and mappings (note the 'vrf' option and  'match-in-vrf' which is essential when using VRFs):

ip nat pool nat-1c-pool 131.111.184.1 131.111.184.1 netmask 255.255.255.0

ip nat inside source list nat-1-clients pool nat-1c-pool vrf nat-1_vrf match-in-vrf overload

!

ip nat pool nat-2c-pool 131.111.185.1 131.111.185.1 netmask 255.255.255.0

ip nat inside source list nat-2-clients pool nat-2c-pool vrf nat-2_vrf match-in-vrf overload

The configure the outside and inside interfaces, putting them in the appropriate VRFs and configuring NAT.  Note that we need HSRP (with different priorities across both contexts, to balance load) on the inside as that is used as a static route destination by the connecting router.  However, we don't need this on the outside as we're using different outside addresses on each router (131.111.184.2 and 131.111.185.2, respectively):

interface Ethernet1/0.1981

 description nat-1-outside

 vrf forwarding nat-1_vrf

 encapsulation dot1Q 1981

 ip address 131.111.184.250 255.255.255.0

 no ip proxy-arp

 ip nat outside

!

interface Ethernet1/0.1982

 description nat-1-inside

 vrf forwarding nat-1_vrf

 encapsulation dot1Q 1982

 ip address 193.60.92.37 255.255.255.248

 no ip proxy-arp

 ip nat inside

 standby version 2

 standby 162 ip 193.60.92.38

 standby 162 timers 1 3

 standby 162 priority 200

 standby 162 preempt

!

interface Ethernet1/0.1983

 description nat-2-outside

 vrf forwarding nat-2_vrf

 encapsulation dot1Q 1983

 ip address 131.111.185.250 255.255.255.0

 ip nat outside

!

interface Ethernet1/0.1984

 description nat-2-inside

 vrf forwarding nat-2_vrf

 encapsulation dot1Q 1984

 ip address 193.60.92.45 255.255.255.248

 no ip proxy-arp

 ip nat inside

 standby version 2

 standby 164 ip 193.60.92.46

 standby 164 timers 1 3

 standby 164 priority 190

 standby 164 preempt

Finally, a bit of static routing for the inside and outside destinations, across both VRFs:

ip route vrf nat-1_vrf 0.0.0.0 0.0.0.0 Ethernet1/0.1981 131.111.184.254

ip route vrf nat-1_vrf 172.16.0.0 255.248.0.0 Ethernet1/0.1982 193.60.92.33

ip route vrf nat-1_vrf 172.24.0.0 255.252.0.0 Ethernet1/0.1982 193.60.92.33

ip route vrf nat-1_vrf 172.28.0.0 255.254.0.0 Ethernet1/0.1982 193.60.92.33

ip route vrf nat-1_vrf 172.30.0.0 255.255.0.0 Ethernet1/0.1982 193.60.92.33

!

ip route vrf nat-2_vrf 0.0.0.0 0.0.0.0 Ethernet1/0.1983 131.111.185.254

ip route vrf nat-2_vrf 172.16.0.0 255.248.0.0 Ethernet1/0.1984 193.60.92.41

ip route vrf nat-2_vrf 172.24.0.0 255.252.0.0 Ethernet1/0.1984 193.60.92.41

ip route vrf nat-2_vrf 172.28.0.0 255.254.0.0 Ethernet1/0.1984 193.60.92.41

ip route vrf nat-2_vrf 172.30.0.0 255.255.0.0 Ethernet1/0.1984 193.60.92.41

And that's all there is to it!

This doesn't give stateful failover (preserving translations), but my simulation only needs to pass traceroutes and pings, so it seems a lot of unnecessary work, as that's completely different on the ASAs.

Nexus management port not sending IGMP Membership Reports

OK - I've spent a day getting annoyed by this!  I was trying to get two Nexus 56128Ps (running NX-OS 7.0(3)) across their management interfaces with CFS to synchronise configuration with switch-profiles.

I had the Mgmt0 interfaces connected to a Cisco 2960 as access ports, with no other connections in that VLAN and everything worked fine.

However, when I tried to connect an uplink from the 2960 to our main network (on a test VLAN) synchronisation broke with show switch-profile status reporting that the Peer is unreachable.  Disconnecting the cable fixed the problem again, immediately.

The problem

After a lot of mucking about, this turned out to be an IGMP issue - the Management0 port on the Nexus switches advertise their presence to each other using multicast messages to a group (239.255.70.83).  However, they weren't sending IGMP Membership Report messages to indicate they themselves want to join the group, preventing the the announcements from reaching each other.

When the switch was not connected to the rest of the network, there was no IGMP Querier, so the switch resorted to flooding multicast traffic.  However, when connected to the main network, the IGMP Membership Query messages from the router started reaching the 2960 and it started to limit flooding.

Pulling the uplink cable from the 2960 immediately aged out the Querier and flood recommenced.  However, if the VLAN was severed in a way not known to the 2960 (e.g. removing the VLAN from the upstream switch), the Querier would take 3 minutes to expire (as expected) before things began to work again.

After some poking about, fiddling around with the configuration of the router, it appears that IGMPv2 is supported by the management interface but IGMPv3 (which is our default) is not.

The fix

Fixing this could be solved in one of three ways:

• Disabling multicast routing on the VLAN,
• Changing the IGMP version to 2 (instead of 3), if this has been raised, or
• Disabling IGMP Snooping on the switches on the management VLAN (e.g. no ip igmp snooping vlan XXX)

I can't find mention of this in the Cisco documentation, nor a way of changing the IGMP version on the Nexus 56128Ps.